West N6401 Instruments/Controls

West Control Solutions 6400 1/16 DIN Temperature/Process Profile Control

SKU: N6401

West 1/16 DIN Temperature/Process Control, Universal Input, Self Tuning, Profile (Ramp/Dwell) Control. Includes RaPID (Fuzzy Logic).

Not rated yet
0
  • $574.00
Out of stock

ALL CONFIGURATIONS 1-3 WEEKS
The 6400 is an advanced profile control that includes times ramp/dwell setpoint profiling.Up to (4) programs each with up to (16) segments can be stored.

6400 Profile Controller
  • Ramp/Dwell Profile Control
  • Guaranteed Dwell
  • Power failure recovery
  • Event/Profile Active Outputs
  • Remote Start
  • Auto or Manual Tuning
  • Heat/Cool Operation Option
  • Alarms Options
  • Modbus Comms Options
  • Configuration via PC Option
Features

Control Types - Full PID with Pre-tune, Self-tune, RaPID fuzzy logic, Manual Tuning, or On-Off control. Heat only or heat & cool.
Auto/Manual - Selectable from front panel with bumpless transfer.
Output Configuration - Up to 3 possible, for control (Heat & Cool), Alarm or (1) retransmit of Process Value or Setpoint.
Alarm 1 & 2 Types - Process high, process low, SP deviation, band.
Human Interface - 4 button operation, dual 4 digit 10mm & 8mm high LED displays with Red Upper/Green Lower displays plus Run/Hold, Tune, Event & Profile/Control Status LED's.
Manual or PC Configuration - Off-line configuration from serial port to dedicated config socket (comms option not required).

Ramp/Dwell Setpoint Profile Control

Number of Programs 4, each with 16 free-form segments (Ramp/Dwell/End). Max segment length 99 hours 59 minutes
Delayed Start Max 99 hours 59mins delay from initiation to program start
Guaranteed Soak Holds program if PV is outside of specified hold band during dwell segments.
Program Cycles 1 to 9999 or infinite (continuously re-starts program at end)
Ramp Rate Definition Either ramp rate, or time to final setpoint
Power Loss Recovery Hot (continue profile from point of power fail) or Cold (end profile and return to controller mode)

Input

Thermocouple - J, K, R, S, T, B, L & N Scalable within selected range.
RTD - 3 Wire PT100, 50ohm per lead maximum (balanced). Scalable within selected range.
DC Linear - 0-20/4-20mA, 0-50/10-50mV, 0-5/1-5/0-10/2-10V. Scaleable -1999 to 9999, decimal point selectable.
Impedance - >10Mohm for Thermocouple and mV ranges, 47Kohm for V ranges and 5ohm for mA ranges.
Accuracy - +/- 0.25% of input range +/- 1 LSD (T/C CJC better than 0.7C).
Sampling - 4 per second, 14 bit resolution approximately.
Sensor Break Detection - <2 secs (except zero based DC ranges), control O/P's turn off, high alarms activate for T/C and mV ranges, low alarms activate for RTD, mA or V ranges.

Outputs & Options

Control & Alarm Relays - Contacts SPDT 2 Amp resistive at 240V AC, >500,000 operations.
Control SSR Outputs - Drive capability >4.2V DC in 1Kohm min
Solid State (Triac) Outputs - 0.01 to 1 Amp AC 20 to 280V, 47 to 63Hz.
Control DC Outputs - 0-20/4-20mA into 500ohm max, 0-10/2-10/0-5V into 500ohm min. Accuracy typically +/- 0.25%.
Communications - 2 Wire RS485, 1200 to 19200 Baud, Modbus.
Digital Input - Remote Run/Hold for profile control using volt free or TTL input. Hold = -0.6 to 0.8V or contact open, Run = 2-24V or contact close.

Operating & Environmental

Temperature & RH - 0 to 55C (-20 to 80C storage), 20% to 95%RH non-condensing.
Power Supply - 90-264Vac 50/60Hz (standard); 4VA ; 20-55Vac 50/60Hz, 22 to 65VDC (option) & 22-65Vdc (option) 4W.
Front Panel Protection - IEC IP66 (Behind panel protection is IP20).
Standards - CE, UL & ULc. recognized.

Additional Information


Click to contact ISE with application assistance, product selection help or models not listed.   Additional models are available.

    • SKU
      N6401
    • Weight
      3 lbs
  • Input
    0-800F J T/C, 0.0-800.0F J T/C, 0.0-450.0C J T/C, 0-1600F J T/C, 0-1000C J T/C, 0-2500F K T/C, 0-1373C K T/C, -199.9 - 999.9F K T/C, -128.8 - 537.7C K T/C, -199.9 - 752.0F T T/C, -128.8 - 400.0C TK T/C, 0-450C J T/C, -400 - 752F T T/C, -240 - 400C T T/C, 32 -3198F R T/C, 0 - 1759C R T/C, 32 -3204F S T/C, 0 - 1762C S T/C, 211 - 3315F B T/C, 100 - 1824C B T/C, 32 - 2551F N T/C, 0 - 1399C N T/C, -328 - 1401F PT100 RTD, -128.8 - 537.7C PT100 RTD, 0 - 20 mA Linear, 4 - 20 mA Linear, 0 - 50 mVDC Linear, 10 - 50 mVDC Linear, 0 - 5 VDC Linear, 1 - 5 VDC Linear, 0 - 10 VDC Linear, -199.9-999.9F PT100 RTD, -199 to 800C PT100 RTD, 2 - 10 VDC Linear
  • Output #1
    (1) Relay (Standard), (2) SSR Drive, (8) Triac, (7) Linear 4-20mADC, (4) Linear 0-20mADC, (5) Linear 0-5VDC, (3) Linear 0-10VDC
  • Output #2
    (4) Linear 0-20mADC Retransmit, (5) Linear 0-5VDC Retransmit, (3) Linear 0-10VDC Retransmit, (2) SSR Drive (Low Process Alarm), (0) None, (6) Linear 2-10VDC Retransmit, (8) Triac (Low Process Alarm), (2) SSR Drive (High Process Alarm), (8) Triac (High Process Alarm), (1) Relay Event Output, (1) Relay (Low Process Alarm), (1) Relay (High Alarm), (7) Linear 4-20mA Retransmit, (1) Relay (Cool), (2) SSR Drive (Cool), (8) Triac (Cool), (7) Linear 4-20mA, (4) Linear 0-20mADC, (5) Linear 0-5VDC, (3) Linear 0-10VDC, (6) Linear 2-10VDC, (1) Relay - Deviation Alarm
  • Output #3
    (0) None, (1) Relay (Low Process Alarm), (1) Relay (High Process Alarm), (1) Relay Event Output, (1) Relay - High Process Alarm, (1) Relay - Deviation Alarm, (1) Relay - Band Alarm, (2) SSR Drive, (7) Linear 4-20mADC Retransmit PV, (4) Linear 0-20mADC Retransmit PV, (5) Linear 0-5VDC Retransmit PV, (3) Linear 0-10VDC Retransmit PV, (7) Linear 4-20mADC Retransmit SP, (4) Linear 0-20mA Retransmit SP, (3) Linear 0-10VDC Retransmit SP, (5) Linear 0-5VDC Retransmit SP
  • Options
    (0) None, (3) Digital Input (Remote Start/Hold), (1) RS485 Communications
  • Power Supply
    (0) 90-264 VAC Powered, Select
  • Display Color
    (2) Red Upper - Green Lower, Select
  • Manufacturer
    West
  • EC44-0
    • Power Supply
      Select
  • Agency Listing
    • UL
      Yes
    • cUL
      Yes
    • CE
      Yes

Related products

Customers who viewed this product also bought

Footer navigation